Diamondback-fitness 700U User Manual download pdf (Page 9)

7 00 SERIES OWNER’S MANUAL

700U Assembly Instructions

Frame Assembly

1. Unscrew two M8 x 20mm bolts from the rear stabilizer bar.

2. Place rear stabilizer bar under rear main frame body and align

screw holes.

3. Insert and tighten these two M8 x 20mm screws using a 5mm

Allen wrench.

4. Install seatpost by sliding it into seatpost receptor.

Console Mast Assembly

1. Install console mast adapter/cover onto console mast.

2. Insert the main wire harness into the bottom opening of the con-

sole mast tube. Push the harness up the tube until the connector

of the harness appears in the opening at the top of the tube.

WIRING HARNESS INSTALLATION TIP: Straighten the loops

of the wiring harness so that it can slide smoothly into the

console mast. Hold the bottom of the console mast next to

the console mast receptor and point the top of the console

mast downward.

3. Install the console mast by sliding it into the console mast re-

ceptor while pulling the wiring harness. This will keep the slack

out of the harness so the wires will not get pinched and short

out. Insert and tighten two M8 x 40mm screws and washers us-

ing a 5mm Allen wrench. Be sure not to pinch wire harness while

tightening these two screws.

4. Snap console mast adapter/cover into top of sidecase.

Handlebar Assembly

1. Insert the hand pulse harness through the opening of the con-

sole mast and out the top of the console mounting plate.

2. Assemble the handlebar onto the mount and insert and tighten

the three M8 x 12mm screws using a 5mm Allen wrench. Be sure

not to pinch the hand pulse harness during this procedure as

this will damage the electronic console.

3. Insert and install handlebar cover onto handlebar and tighten

one M8 x 12mm screw on the bottom of the handlebar cover.

Console Assembly

1. Connect both plugs, from the main wiring harness and hand pulse

wiring harness, to the plug receptors on the backside of the con-

sole taking care to install correctly (see plug alignment marks).

WIRING HARNESS INSTALLATION HINT: Any excess wiring

must be carefully inserted (“stored”) back into the console

mast before installing the console onto the console mounting

plate.

2. Fasten the console to the console mounting plate with the four

M5 x 12mm screws and washers using a Phillips screwdriver.

Saddle Assembly

1. Assemble saddle onto seatpost.

2. Tighten the affixing nut and washer using a 17mm open-end

wrench.

SADDLE ANGLE ADJUSTMENT HINT: Hold the rear of saddle

in the optimum comfort position and tighten the nut at the

same time.

Pedal Assembly

1. Use a 15mm open-end wrench to firmly affix the pedals to the

cranks.

2. The left and right pedals are different and are denoted as right or

left on the bottom of each pedal. NOTE: Left pedal threads coun-

terclockwise.

3. Retighten cranks after approximately 10 hours of use.

Waterbottle Assembly

1. Place the bottle holder on the console mast. Insert and tighten

the two M5 x 12mm screws using a screwdriver.

2. Snap the waterbottle into the bottle holder.

Transformer Assembly

1. Plug transformer into plug receptor located on the rear/bottom

side of main frame.

2. Plug the transformer into power outlet. NOTE: Be sure to use

right transformer for your power outlet, 110V or 220V.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 21 22

Comments to this Manuals

No comments

Diamondback-fitness 700U User Manual Page 9

Comments to this Manuals

Related products and manuals for Fitness accessories Diamondback-fitness 700U