Diamondback-fitness 700U User Manual download pdf (Page 11)

7 00 SERIES OWNER’S MANUAL

700R Assembly Instructions

Rear Frame & Seat Assemblies

1. Unscrew two M8 x 20mm bolts from the rear stabilizer bar.

2. Remove the hand pulse harness which is stored in the seat track

receiving tube. Assemble seat frame to seat track. Cut off tywrap

and remove the seat lock retainer that holds the seat lock in the

locked position (see diagram 2). Make sure to adjust the seat

tightening mechanism so it will not blind with the seat track upon

installation.

3. Install seat track assembly by sliding seat track onto seat track

receptor. Be careful not to pinch the coiled hand pulse harness

during seat track installation. Securely fasten the seat track us-

ing two M8 x 15mm screws and the seat track stops using two

M8 x 20mm screws and washers with a 5mm Allen wrench. Take

note that the seat track stops must be installed on the screws

closest to the seat track cover (see diagram). Do not over tighten

the seat track stop screws.

4. Place rear stabilizer bar under the seat track and align the screw

holes.

5. Insert and tighten two M8 x 20mm screws using a 5mm Allen

wrench.

6. Install seat frame handlebar onto the seat frame using four M8 x

15mm screws and washers using a 5mm Allen wrench.

7. Connect the plug from the hand pulse wiring harness of the seat

handlebar to the plug receptor of the retracting cable hanging

out of the sidecase. Secure the hand pulse harness on the back

and bottom of the seat frame by tightening the harness on the

cord clamps with the two tywraps included in the hardware box.

8. Install seat back and seat pad onto the seat frame using four M6

x 15mm screws and split washers (for each pad).

Console Mast Assembly

1. Install console mast adapter/cover onto console mast.

2. Run both wiring harnesses through the bottom of console mast

to the top of console mast opening. Pull the harnesses until just

tight, DO NOT PULL HARD.

WIRING HARNESS INSTALLATION HINT: Straighten the loops

of the wiring harnesses and twist both harnesses so that it

can slide smoothly into the console mast.

3. Install the console mast by sliding it into the console mast re-

ceptor while pulling the wiring harness. This will keep the slack

out of the harness so the wires will not get pinched and short

out. Insert and tighten four M8 x 12mm screws using a 5mm

Allen wrench. Be sure not to pinch wiring harnesses while tighten

screws.

4. Snap console mast adapter/cover into top of sidecase.

Console Assembly

1. Connect the plugs from the main wiring harness and hand pulse

to the plug receptors on the backside of the console taking care

to install correctly (see plug alignment marks).

WIRING HARNESS INSTALLATION HINT: Any excess wiring

must be carefully inserted (“stored”) back into the console

mast before installing the console onto the console mast.

2. Fasten the console to the console mast with the four M5 x 12mm

screws and washers using a Phillips screwdriver.

Pedals Assembly

1. Use a 15mm open-end wrench to firmly affix the pedals to the

cranks.

2. The left and right pedals are different and are denoted as right or

left on the bottom of each pedal. NOTE: Left pedal threads coun-

terclockwise.

3. Retighten cranks after approximately 10 hours of use.

Waterbottle Assembly

1. Place the bottle holder on the console mast. Insert and tighten

the two spacers and two M5 x 12mm screws using a screw-

driver.

2. Snap the waterbottle into the bottle holder.

Transformer Assembly

1. Plug transformer into plug receptor located on the rear/bottom

side of main frame.

2. Plug the transformer into power outlet. NOTE: Be sure to use

right transformer for your power outlet, 110V or 220V.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 21 22

Comments to this Manuals

No comments

Diamondback-fitness 700U User Manual Page 11

Comments to this Manuals

Related products and manuals for Fitness accessories Diamondback-fitness 700U